ASA recommends a minimum of 7 days curing to help control shrinkage issues in young concrete sections. Lack of curing, and exposure to windy, hot or dry conditions will certainly increase the potential for shrinkage and cracking of the concrete. Lack of curing will prevent the concrete from achieving its maximum potential strength. However, shotcrete generally exceeds the minimum 4000 psi (28 MPa) 28-day compressive strength ASA recommends, and required strength depends on the pool design. If you want to confirm the compressive strength of your in-place concrete, cores taken from the pool should be tested for compressive strength by a qualified testing lab. ASTM C1604 Standard Test Method for Obtaining and Testing Drilled Cores of Shotcrete gives guidance on taking cores from existing structures. A minimum 3” diameter core is recommended. Before coring it is recommended to use ground penetrating radar (GPR) or similar equipment to identify the location of reinforcing in the pool section, and then take cores to avoid cutting through the reinforcing wherever possible. The core holes would then need to be filled with a high strength, non-shrink cementitious grout. Once you learn the actual strength, you would need to check with the pool design engineer to verify the strength is adequate for the design. If the strengths are not adequate, you should consult with the pool designer or a licensed professional engineer experienced in pool design for potential solutions.
I modified an existing pool and had a new 20 ft (6 m) wall built that was subsequently back filled. The rebar was epoxied and tied into existing pool wall/floor. The wall is 4.5 ft to 6 ft (1.3 to 1.8 m) tall. 60 days later we have two vertical hairline cracks that run top to bottom. I watered the wall properly and there are no cracks in the other sections we shot (spa, etc). We backfilled 12 days after the wall was shot with hand equipment only. The sample test taken when shooting came back at 6500 psi (4.1 MPa). The original pool bottom is below the wall and has no issues. The wall appears to be 12 to 14 in. (300 to 350 mm) thick from top to bottom. My question is if the wall was shot too thick would the lack of additional rebar cause the wall to fail? And is the necessary course of action to demo the entire wall and reinforce the rebar, then shotcrete again?
There are many variables that can cause cracking. Vertical cracking is often the result of drying shrinkage of the concrete. You said you cured (watered) the wall properly, but don’t give any specifics. ASA recommends a minimum of 7 days of curing, with a wet cure preferred over a spray-applied membrane. You should have a licensed engineer evaluate the structural sections, and determine if there were any problems with the amount or placement of reinforcing in your wall section.
What is the R-Value per inch of shotcrete?
Since shotcrete is simply a placement method for concrete, the R-value is the same as cast concrete. ACI 122R-14, “Guide to Thermal Properties of Concrete and Masonry Systems,” would be a good reference.
We have a backwash tank on a waste water treatment plant which is made by a secant wall. The lower area for this structure will receive a shotcrete liner approximately 12 ft (3.7 m) tall on average, the interior perimeter of the structure includes 104 lineal ft (32 m) of unreinforced and 440 ft (134 m) reinforced sections which are a 12 in (300 mm) minimum thickness. The drawings call for vertical control joints with waterstop approximately every 30 ft (9 m). We don’t believe the control joints are necessary and could achieve the same desired performance with one monolithic installation of the shotcrete. Are the control joints really necessary when you are installing the shotcrete against a solid secant wall which does not contain any control joints?
By control joints, we assume you mean contraction joints. Shotcrete is a placement method for concrete. All normal concrete experiences drying shrinkage that creates a volume change in the hardened concrete. Though shotcrete has a lower w/cm than most form and pour concrete, it will still undergo shrinkage. In being shot on an existing concrete wall the shotcrete liner will be restrained by the bond to the substrate and the restraint of the horizontal volume change from shrinkage can create internal tensile stresses in the concrete. This is likely the reason the designer has specified contraction joints in the section. 30 ft (9 m) spacing between joints is common in new construction of concrete tanks. The question becomes whether the bond of the shotcrete to the existing substrate is high enough to restrain the volume change and prevent cracking along the hundreds of lineal feet of wall you will be lining. The thickness of the lining, the type and duration of curing, the concrete mix design, the strength of the concrete, the strength of the substrate, the quality of shotcrete application, proper surface preparation and exposure to seasonal temperature changes will impact the effect of the volume change of the lining. With the many variables we’ve pointed out you can see there isn’t a clear answer that covers all situations. We recommend you discuss your opinion with the designer or consult with a professional engineer experienced in shotcrete repairs to fully evaluate the specific structural sections you’re shotcreting.
Our company has been working on the design of a concrete pond for winery wastewater and the contractor proposed to replace the concrete liner with a geomembrane (canal 3) covered by shotcrete. Have you seen cases of this application being successful for wastewater holding? As an alternative we are considering applying the shotcrete over a clay liner. Are there any concerns or recommendations for this approach?
Shotcrete is a placement method for concrete. Shotcrete has been successfully used for over 70 years in thousands of industrial wastewater treatment/storage tanks, as well as replacement lining of sewers and manholes. Thus, exposure of the shotcreted pond to wastewater should be as good or likely even better than the original cast concrete liner. Long term durability of the shotcreted section will be dependent on the concrete mixture design. Many contractors use supplemental cementitious materials (SCMs) like silica fume or fly ash to improve the pumping or shooting characteristics of the mix. These SCMs also help to reduce permeability, increase strength, and thus make the concrete more durable. Fly ash also has the benefit of adding some sulfate resistance that would be beneficial in wastewater exposure conditions. Shotcrete is often shot on geomembranes or directly on the subgrade soils if they are stable enough to hold the impact, and weight of the shotcrete.
We have a pool designed with the cast-in-place concrete construction method in mind. The project has been awarded to a dry-mix gunite contractor. To accommodate the contractor’s placement method, we have been working with him on the details. They are planning on casting the floor and shooting the walls. There are two main areas of concern/questions that we have. First is in regard to the air entrainment and the admixtures that are appropriate for gunite. They have not used air-entrainment admixtures prior to this project. What is the effect to durability without using air? What are the workability effects of adding air entrainment? Which product is recommended? Second, we have specified a hydrophilic waterstop between the cast-in-place floor and the wall. With the walls using a gunite application, what is the best method for preventing water infiltration in the construction joint? Does it hurt the integrity of the joint by installing a hydrophilic waterstop? If the water stop is omitted, what does the surface roughness need to be to provide a monolithic-type connection?
Air entrainment will generally slightly reduce the compressive strength of concrete, but significantly increase the resistance to freezing-and-thawing exposure. Dry-mix shotcrete (gunite) is generally a very paste-rich mixture. With modern cements, the normal 28-day compressive strengths easily exceed commonly specified compressive strengths. ASA recommends a minimum of 4000 psi (28 MPa) for shotcrete, and 4000 psi to 5000 psi (28 to 34 MPa) strengths are routinely specified.
- Air entrainment increases the workability. The small air bubbles act as a form of lubricant to ease internal friction between the concrete mixture components.
- You should contact one of our material supplier members to see what they offer. You can use our Buyers Guide at shotcrete.org/products-services-information/buyers-guide/, and limit your search to “Admixture Sales” with the “Air-Entraining” subcategory.
- Quality shotcrete shot against a properly prepared concrete substrate should produce a watertight interface. The hydrophilic waterstop at the joint could be considered a secondary method of making the joint watertight. Though not necessary, it is kind of a “belt and suspenders” approach with a relatively low cost to place.
- In shotcrete construction, surface preparation between layers to provide full bond is important. ACI 506.2-13, “Specification for Shotcrete,” specifically addresses this in the requirements of Sections 3.4.2.1 and 3.4.2.2 that state:
“3.4.2.1 When applying more than one layer of shotcrete, use a cutting rod, brush with a stiff bristle, or other suitable equipment to remove all loose material, overspray, laitance, or other material that may compromise the bond of the subsequent layer of shotcrete. Conduct removal immediately after shotcrete reaches initial set.
“3.4.2.2 Allow shotcrete to stiffen sufficiently before applying subsequent layers. If shotcrete has hardened, clean the surface of all loose material, laitance, overspray, or other material that may compromise the bond of subsequent layers. Bring the surface to a saturated surface-dry condition at the time of application of the next layer of shotcrete.”
For more details on bond between shotcrete layers, you may want to refer to an article in the Spring 2014 issue of Shotcrete magazine, “Shotcrete Placed in Multiple Layers does NOT Create Cold Joints.” A PDF of the article can be found at shotcrete.org/wp-content/uploads/2020/01/2014Spr_TechnicalTip.pdf.
I had a concrete pool shell installed using gunite (dry shotcrete method) in July 2013. It was never finished due to unfortunate circumstances and has been exposed to the elements of weather over the last 2 years, mostly filled up with water from rain and, in the colder months, frozen like a pond. We would like to finish the pool but were told by the pool company that the concrete looked odd and we should have it strength tested. We had core samples taken from the walls and floor from a certified testing lab. The results from the six samples ranged from 1700 to 2200 psi (12 to15 MPa). When the pool was blown on July 3, 2013, it was to achieve 4000 psi (28 MPa) compressive strength in 28 days. Is it normal for the shotcrete strength to have weakened so much?
Properly produced concrete material shotcreted in place should gain strength over time, not lose strength. ASA recommends that concrete placed by the shotcrete method have a minimum compressive strength at 28 days of 4000 psi (28 MPa). Coring does damage the sample somewhat, so it is common to require core strength to meet 85% of the specified compressive strength. Cores should be no less than a nominal 3 in. (76 mm) in diameter for representative results because smaller cores (less than 3 in. [76 mm] diameter) are more subject to damage from the core extraction, affecting the reported strength. Thus, at 85% of 4000 psi (28 MPa) the minimum should be 3400 psi (23 MPa). Based on the reported values, and assuming a 3 in. (76 mm) diameter or greater core, the concrete strength is well below ASA’s recommended strength, and the strength you originally specified in 2013.
I am currently involved with the design of an unreinforced masonry building retrofit. Could you point me toward resources concerning the seismic behavior of a reinforced shotcrete masonry wall? I am interested in learning more about the force (shear) transfer between the masonry/shotcrete interfaces.
Shotcrete is a placement method for concrete. Thus, seismic design for concrete is applicable to shotcrete placement. Here’s a link to an article in the Winter 2009 issue of Shotcrete magazine, titled “Seismic Retrofit of Historic Wing Sang Building,” that details the seismic retrofit of a brick building in Vancouver, BC, Canada: https://shotcrete.org/wp-content/uploads/2020/01/2009Win_SCM01pg08-12.pdf.
A second article from 1999, “Seismic Reinforcing of Masonry Walls with Shotcrete,” also gives some input on the design: https://shotcrete.org/wp-content/uploads/2020/01/1999Fal_Snow.pdf. In general, the structural engineer must evaluate the condition of the existing masonry structure and determine whether the added shotcrete sections will be supplementing the existing capacity or providing the full resistance to seismic loads.
Our shotcrete mixture needs to be NSF 61 certified. We have been able to obtain certification of all components with the exception of reinforced fiber. Is there or does fiber reinforcing need NSF 61 approval?
Each manufacturer of concrete constituents needs to have their products tested by NSF if they want NSF 61 certification. Whether the fibers need NSF 61 certification is an issue with the local authority having jurisdiction for exposure of components to potable water supply systems in your state. Generally, this is the state EPA-type agency, but maybe a federal agency if on a federal project.
We don’t maintain a database of manufacturer products that meet NSF 61. However, you can readily identify contacts for the fiber manufacturers who are ASA corporate members with our Buyers Guide at https://shotcrete.org/products-services-information/buyers-guide/. When entering the Buyers Guide, you can select “Fiber + Reinforcement Sales” and the fiber type subcategory to get a list of our member fiber suppliers.
I just had a swimming pool built and everything I have read online says that the gunite shell has to be sprinkled with water for several days after the pour. My pool builder says they never do it, and, when I asked why, I’m just told that’s the way they do it. I told them I am worried because every other pool builder says to do that except the one I hired and I can get no answer as to why. Is this an acceptable practice? I am worried that years down the line I may have a problem. I live in Oviedo, FL, and the weather has been in the low 70s and the humidity not particularly high. They did hit the water table and have a pump running—would any of this have an impact?
ASA recommends a minimum of 7 days curing for all exposed shotcrete surfaces. Wet curing is preferred to supply additional water to the concrete surface. If a spray-on curing membrane is used instead of water curing, the material should be applied at twice the manufacturer’s recommended rate for formed surfaces. Curing is important to allow the concrete to develop as much strength as possible and to help resist cracking from internal shrinkage of the concrete. Low humidity, wind, and exposure to sun will increase the need for proper curing. If the site is dewatered, the groundwater is below the concrete work, and not effective in curing the exposed shotcrete surface. The American Concrete Institute (ACI) has an excellent reference, ACI 308R-01, “Guide to Curing Concrete.” It appears your contractor is not following the industry standards as documented by ACI.