The ASA Technical Questions and Answers is a free service offered to all users, but primarily intended for engineers, architects, owners and anyone else who may be specifying the shotcrete process and/or has need for a possible answer to a technical question.
User agreement: The answers provided to submitted questions are intended for guidance in planning and executing shotcrete applications. This information is intended only for the use of individuals who are competent to evaluate the significance and limitations of its content and recommendations, and who will accept responsibility for the application of the material it contains. The American Shotcrete Association provides this information based on the best knowledge available to them and disclaims any and all responsibility for the information provided. The American Shotcrete Association will not be liable for any loss or damage arising therefrom.
If you are unable to find what you are looking for in the archive, then submit a new technical question.
StructuralQ Is shotcrete a viable option to encase galvanized steel beams at a coal unloading facility to protect them from impact and abrasion? Will the galvanizing on the steel inhibit bonding?
Yes, shotcrete would be suitable for this application. A well-installed shotcrete lining will be durable and protect the steel from impact, abrasion, and from the acid attack that occurs from sulfur in the coal. Shotcrete is used to cover both the steel hopper walls and to encase the steel beams. Calcium aluminate cement is typically recommended for coal bunkers because of the mild acid condition that occurs that can attack the steel. Whether or not the steel beams are galvanized or not is irrelevant because the shotcrete will not bond well enough to any steel surface without welded studs and mesh to hold it in place. The beams will need to have studs welded and mesh installed around the beams for the shotcrete placement. With galvanized steel it is often necessary to grind off a spot of the galvanized coating at the spot of each stud weld location to properly weld the studs.
StructuralQ Is shotcrete used as a canal liner?
Shotcrete has been used for canal lining throughout the United States. The Bureau of Reclamation published a study on Canal Lining Test Sections constructed in the Bend, OR, area and studies the durability at 5 and 10 years. Shotcrete is a very viable means of placing canal linings. Basically, shotcrete is a method of placing concrete. Care should be taken to ensure that the mixture is designed to withstand the local environmental conditions, such as using air-entraining admixtures to ensure durability due to exposure to freezing and thawing. ACI 506R-05, “Guide to Shotcrete,” contains a lot of useful information in evaluating and using shotcrete in a variety of applications, including canal linings. If liquid-tightness and long-term durability of the canal lining are important, provisions of ACI 350/350R-06, “Code Requirements for Environmental Engineering Concrete Structures and Commentary,” should also be considered in the design of canal lining reinforcement, cover, and joints.
StructuralGeneralQ Is there a guide to determining pressure applied to a form during shotcrete placement? I have seen references to 50 lb/ft2 (240 kg/m2) but no backup to this. Is the ACI formwork design guide applicable to shotcrete in some way?
Since shotcrete is pneumatically placed against a one-sided form there is no liquid concrete pressure against the form. When bench shooting vertical walls the majority of pressure from the high velocity impact is carried by the previously placed concrete as the concrete is stacked. Plus, this pressure is very localized, only affecting a small zone immediately adjacent to the impact area of the material stream. Here is an article on a research project that quantified the force https://shotcrete.org/wp-content/uploads/2020/05/2007Sum_TechnicalTip.pdf
From the paper conclusion “In normal spraying conditions, wet- and dry-mix shotcretes produced a force on the panel of about 45 and 20 lb (200 and 90 N), respectively. The maximum load recorded is 87 lb (389 N) and it was observed in simulating a water plug.”
If your shotcrete form is exposed to wind forces before placing shotcrete, you may want to consider the wind pressure that may be expected across the entire form during construction to keep the form intact. This should be much less than the 50 lb/ft2 pressure you mention. ACI formwork design is intended for cast concrete where liquid concrete is contained within a two-sided form and is NOT applicable to shotcrete placement. Some sources show a 60 mi/hr (100 km/ hr) wind exerting about 10 lb/ft2 (50 kg/m2) on a vertical wall.
StructuralQ Our company has been working on the design of a concrete pond for winery wastewater and the contractor proposed to replace the concrete liner with a geomembrane (canal 3) covered by shotcrete. Have you seen cases of this application being successful for wastewater holding? As an alternative we are considering applying the shotcrete over a clay liner. Are there any concerns or recommendations for this approach?
Shotcrete is a placement method for concrete. Shotcrete has been successfully used for over 70 years in thousands of industrial wastewater treatment/storage tanks, as well as replacement lining of sewers and manholes. Thus, exposure of the shotcreted pond to wastewater should be as good or likely even better than the original cast concrete liner. Long term durability of the shotcreted section will be dependent on the concrete mixture design. Many contractors use supplemental cementitious materials (SCMs) like silica fume or fly ash to improve the pumping or shooting characteristics of the mix. These SCMs also help to reduce permeability, increase strength, and thus make the concrete more durable. Fly ash also has the benefit of adding some sulfate resistance that would be beneficial in wastewater exposure conditions. Shotcrete is often shot on geomembranes or directly on the subgrade soils if they are stable enough to hold the impact, and weight of the shotcrete.
StructuralQ Our general contracting firm is working on a project with a very tight schedule and significant penalties for missing the completion date. It has been suggested that we consider using shotcrete for the below-grade foundation walls. We have been told that we can save significant time by using shotcrete instead of cast-in-place construction. These walls are heavily reinforced. Has this been done successfully elsewhere?
Yes. Heavily-reinforced shotcrete has been used in California for over 50 years in response to the need to retrofit structures to resist earthquake damage. The shotcrete contractor must demonstrate his ability to shoot test panels with the same reinforcement as designed into the project. By using an experienced and qualified shotcrete contractor, it is possible to achieve cost savings of almost 30% and time savings approaching 50%.
StructuralGeneralQ The Los Angeles City Bulletin states that no bars over No. 8 (No. 25) shall be used. The structural engineer has No. 10 (No. 32) bars in the columns. I am being told the test panel will get this approved but my City Inspector is balking a little. Is there a publication or code somewhere that allows the test panel to supersede the LADBS Bulletin?
The International Building Code (IBC), Section 1913, allows for larger bars as long as it is demonstrated in a Preconstruction Test Panel. However, the Local Building Code likely takes precedence over the IBC. You may want to present IBC Section 1913, which requires anything over a No. 5 (No. 16) bar to be proven in a Preconstruction Test Panel.
There have been many projects shot in Los Angeles County subject to the LADBS with bar sizes larger than No. 8 bars. ASA is not in a position to give you project references, but perhaps our local members can.
Properly encasing No. 10 (No. 32) bars can be challenging, and should only be attempted by qualified contractors using ACI Certified Nozzlemen who have previous successful experience doing this type of work. You may use our online Buyers Guide to find an ASA corporate member consultant or contractor to assist you.StructuralQ There is a pre-stabilized steep slope (nailing is used along with shotcrete). The client wishes to benefit from the maximum achievable area in plan and is asking for excavation of the stabilized slope to shift back the wall face around a few meters. The new stabilization plan shall include a safe gradual excavation of the existing wall from top to bottom along with the destruction of the existing shotcrete face, reinforcement, and the installed nails. What is the most common destruction method for the existing shotcrete? At the same time, I think pulling out the nails using hydraulic jacks would be applicable.
The existing shotcrete can be removed by many methods, such as using a Hoe-Ram. The existing soil nails could be removed as suggested or left in place and trimmed back to some distance behind the new plane. We would assume that this work would be done from the top down installing new soil nails and shotcrete facing in lifts of approximately 4 to 5 ft (1.2 to 1.5 m).
StructuralQ We are applying shotcrete in a slope (8 in. [200 m]) to make it stable. The shotcrete wall has a length of 330 ft (100 m). Do we need to specify construction and an isolation joint? In case it is required as well as an isolation joint, does the separation between joints need to be 30 ft (9 m)? Where can I find information about joints for shotcrete?
Shotcrete is a placement method for concrete. Thus, you should place movement joints (contraction, expansion, isolation) as would be required by your local design codes for concrete. Joint spacing will depend on the amount of reinforcement used in the section to resist temperature and shrinkage volume changes. Construction joint spacing can be determined by the contractor depending on their production rates. Properly prepared construction joints will act as monolithic concrete as long as the joints are properly prepared and proper concrete materials, equipment, and placement techniques are used by the shotcrete contractor. Construction joints should be roughened, cleaned, and then dampened to saturated surface-dry conditions before subsequent shotcrete placement.
The U.S. Bureau of Reclamation has a nice summary document that you may find helpful in your design.
StructuralQ We are building 6 and 8 in. (150 and 200 mm) thick cast-in-place concrete retaining walls with No. 4 (No. 13M) reinforcing bar at 18 in. (450 mm) on center each way. We would like to change to shotcrete as an alternate method of construction. Does the reinforcing bar design have to change for shotcrete application?
Shotcrete would be a great substitute for the retaining wall. Design-wise, the shotcrete is equivalent to concrete because shotcrete is really just a way of placing concrete.
The No. 4 (No. 13M) at 18 in. (450 mm) on-center spacing is not a problem. A No. 4 (No. 13M) bar can be easily encased by a qualified, experienced nozzlemen using either wet- or dry-mix shotcrete. In longer walls, or anywhere where reinforcing bars are lap spliced, the lap splice bars should be spaced apart. ACI 506R-05, “Guide to Shotcrete,” Section 5.4, provides some good guidance on optimizing reinforcing bar layouts for shotcreting. On the issue of lap splices, it says: “If the design allows, direct contact of the reinforcing splices should be avoided. Non-contact lapped bars should have a minimum spacing of at least three times the diameter of the largest bar at the splice.”
Thus, with No. 4 (No. 13M) bars in a lap splice, you should have the reinforcing bars spaced 1.5 in. (38 mm) apart at the splice to allow the shotcrete material to flow around the bar during shooting.
Chapter 8 of ACI 506R-05, “Guide to Shotcrete,” also provides a lot of guidance on proper shooting techniques for a variety of applications, including walls.
StructuralQ We are building a home where some of the outside walls are bricked. Is there a way to use shotcrete over strand board (chipboard)? If so, how and what cost would there be approximately a square foot for the actual shotcrete installed?
More information is needed before answering this correctly. Shotcrete will stick to strand board, but you need some type of reinforcement (wire mesh) to hold it all together. A good cement plaster mix at a lower velocity would be more economical. Contractors who have shotcreted a house in the past will tell you that it is too time consuming for the money involved.