We have a client with a 6 1/2 in. (165 mm) thick reinforced concrete roof slab, the underside of which is in need of repair. There are places where the concrete has spalled, exposing reinforcing bar that has a 3/4 in. (19 mm) cover. There is efflorescence, and there is spalling that does not expose reinforcing bar and some at the steel supporting the concrete slab. In addition, there are hairline cracks and rust spots. Is shotcrete a feasible overhead repair for this situation? What holds the shotcrete to the slab? What is the minimum thickness of shotcrete we should specify? Should we specify shotcrete to be used only at the spalls, cracks, and efflorescence or the whole underside of the slab? Do you have a shotcrete repair procedure that we can put in our specification?

This type of repair is commonly done using the shotcrete process. The extent of the repair is an engineering issue, not a shotcrete issue—shotcrete can and is used for patches and overlays. The shotcrete will adhere to the properly prepared existing concrete. It is installed such that the weight of the plastic shotcrete does not;exceed the adhesion to the existing surfaces; if additional material is needed, it is added at the initial layer or layer set up. The minimum thickness is related to the material used for the repair and the need to establish cover on the existing or added reinforcing. Some repair mortars can be placed as thin as 1/2 in. (13 mm).
Please find a link to a paper on “Concrete Repair by Shotcrete Application”.
The success of the shotcrete repair will be highly dependent upon using a qualified shotcrete contractor and doing an excellent job of preparing the surfaces. Where the reinforcing is exposed, you should require that it be chipped out the entire perimeter allowing for a space of 3/4 in. (19 mm) behind the reinforcing bar so that the repair material can completely encase the reinforcing.

What is the standard method for steel fiber-reinforced shotcrete (SFRS) testing? Are you supposed to core test panels or do you only do that for plain shotcrete? Additionally, is round panel toughness testing on SFRS standard today in the United States?

SFRS is routinely cored from shotcrete test panels or in-place shotcrete linings without difficulty. The shotcrete should, however, have a minimum compressive strength of about 10 MPa (1450 psi) at the time of coring.
Round panel testing of flexural toughness of fiber-reinforced shotcrete to ASTM C1550 is often specified and used for quality control (QC) purposes in tunneling and mining projects in North America and elsewhere (for example, mines in Australia) virtually every day of the year.

We plan to use fiber-reinforced (polypropylene fibers) shotcrete as a brown coat for stucco (three-coat stucco) over a concrete shear wall. Does a maximum thickness of 1.5 in. (38 mm) of shotcrete require any mechanical anchor/connection, or is the bonding strength of the shotcrete layer to the concrete shear wall substrate sufficient?

The addition of fiber will not increase the bond of shotcrete to the concrete shear wall. A 1.5 in. (38 mm) thick layer of properly designed and applied shotcrete should have adequate bond to a properly prepared concrete substrate without additional mechanical anchors. However, exposure conditions, geometry of the wall, shrinkage potential of the shotcrete mixture, application technique, and curing—as well as the age and quality of the shear wall concrete substrate—may affect the bond. These factors should be considered by an engineer experienced with shotcrete overlays in deciding whether additional anchoring is advisable.

In regards to the strength of shotcrete and weather is there a Mine Safety and Health Administration (MSHA) regulation requiring our paste cylinder sample results to be above a certain psi (MPa)?

Shotcrete is normally expected to meet or exceed 4000 psi (27.6 MPa). We are not aware of any specific MSHA requirements. We would suggest you consult a tunnel or mining engineer who is well-versed with shotcrete. Cores taken from field-shot test panels are generally used for the evaluation of compressive strength of shotcrete (ASTM C1140/C1140M-11).

We are a shotcrete contractor in Gold Coast, Australia. We have noticed that in the United States, you use different types of tools for cutting the shotcrete. How do you maintain a plum wall with the shotcrete rods? When a project requires a smooth finish or steel trowel finish, what are the tools and processes that are typically used? Finally, for a structural wall, what is the typical psi (MPa) and size of aggregate used?

The face or surface of shotcrete walls as described are typically established with ground wires or screeds, which assist the person using the shotcrete rod in cutting the wall to the proper plane. The tools typically used to achieve a troweled surface are the shotcrete rod, wood floats, and steel trowels. Typically, shotcrete walls are a minimum of 4000 psi (27.6 MPa) 28-day compressive strength and the aggregate varies from sand only to a blend of sand and 0.375 to 0.5 in. (9.6 to 13 mm) aggregate. Consult our Shotcrete magazine archives for examples at www.shotcreteweb.wpengine.com.

Can shotcrete be effectively used to repair holes in an old 8 ft (2.4 m) diameter storm sewer tunnel constructed of stone/brick/mortar? One of the holes is completely worn through to the earthen backfill material. The other two holes are missing the innermost layer of stone masonry, but the outer layer of masonry is still in place.

The friction coefficient n of well-finished shotcrete for use in Kutter’s equation (and, more streamlined, Manning’s equation) is generally used as 0.012. Shotcrete is used not only to improve flow characteristics of brick, corrugated metal, or any other pipe construction but can also be conventionally reinforced as a structural liner to eliminate the need for liner plates or other pipe-lining alternatives.

To keep shrinkage cracking sufficiently tight so as not to cause reflective cracking in the plaster layer, what is the proper depth of reinforcing steel from the shotcrete surface in swimming pool applications?

This question should be addressed by a qualified engineer with experience in designing swimming pools and well-versed in shotcrete technology. Shotcrete is a method of placing concrete and the parameters that work for concrete cover work for shotcrete.

Good practices for placing shotcrete or concrete include:

  1. Predampening the soil that the concrete/shotcrete is placed against;
  2. Ensuring that the reinforcing bar temperature is not too high; and
  3. Early curing of the shotcrete surface and maintenance of curing for the specified duration. If no duration is specified, a 7-day wet cure is recommended.

Using fibers in the shotcrete/concrete can also help control surface early-age plastic shrinkage cracking.

I have a swimming pool that appears to have shrinkage cracks in the floor. I have tried to inject an epoxy, but the cracks are too small. Do you have any suggestions?

There are a wide variety of epoxies and polyurethanes used for crack injection. Smaller crack widths would require a lower-viscosity material to penetrate the crack. You should contact an engineer or injection specialist experienced in shotcrete and cracking issues to evaluate the cracking and make a specific recommendation for repair. Proper concrete mixture design, placement techniques, and early water fogging and curing can help to reduce plastic shrinkage and drying shrinkage cracking in the future.