The ASA Technical Questions and Answers is a free service offered to all users, but primarily intended for engineers, architects, owners and anyone else who may be specifying the shotcrete process and/or has need for a possible answer to a technical question.
User agreement: The answers provided to submitted questions are intended for guidance in planning and executing shotcrete applications. This information is intended only for the use of individuals who are competent to evaluate the significance and limitations of its content and recommendations, and who will accept responsibility for the application of the material it contains. The American Shotcrete Association provides this information based on the best knowledge available to them and disclaims any and all responsibility for the information provided. The American Shotcrete Association will not be liable for any loss or damage arising therefrom.
If you are unable to find what you are looking for in the archive, then submit a new technical question.
RepairGeneralQ We are applying a new shotcrete shell to an existing building. We are calling for a 5 in. (125 mm) base coat with a 1/4 in. (6 mm) brush-finished flash coat. We are specifying a color admixture for all of the shotcrete. It is a large building and we anticipate several days of shotcrete operations. Would it be wise to allow (or even specify): 1) the color admixture to be used in the flash coat only? 2) all of the flash coat to be applied at once, possibly days after all of the base coat has been installed, to achieve a more uniform final appearance?
If you only need color in the exposed shotcrete surface, just putting color in the flash coat should be adequate as long as the flash coat is continuous across the entire area. You may want to specify the final “flash” layer to be thicker, perhaps 1/2 in. (12 mm) to 1 in. (25 mm) thick. This would help assure consistent color and still allow the finishers to produce a consistent final texture. As long as the concrete materials are the same in the production, you wouldn’t need to shoot the final layer all in one day. Also, be sure curing methods are the same for the entire area as varying moisture can sometimes affect the early appearance of the coloring, though it usually balances out over time.
RepairQ We are going to be using shotcrete for repairs in a parking structure. We have no experience performing this work and will be subcontracting this portion of the job. What should we be watching for when the shotcrete is being applied?
Surface preparation is a critical operation. The substrate must be prepared properly. All deteriorated concrete must be removed. This is generally accomplished with light-duty chipping hammers, scarifiers, or scabblers. The remaining concrete is then sandblasted or waterblasted to remove the concrete “bruised” by the initial removal operation. The objective is to create a clean, sound surface with the proper surface roughness to receive the shotcrete.
After the surface preparation, the substrate must be saturated with clean water and then allowed to dry to a saturated, surface-dry condition immediately prior to shotcreting. Shotcrete should not be applied to a bone-dry surface as the substrate will absorb water in the shotcrete mixture intended for hydration of the cement. Also, a bone-dry surface will tend to allow plastic and drying shrinkage cracks to form. Conversely, a surface that is wet at the time of shotcreting will result in a high water-cement ratio (w/c) at the interface between the substrate and the shotcrete. High w/c at the interface will result in significantly lower bond strengths.
As with all concrete, proper curing and protection is critical. Failure to cure properly will result in lower shotcrete strengths and may cause some delaminations if drying shrinkage causes stresses that exceed early bond strength. Plastic shrinkage cracking and “crazing” may also result from failure to cure and protect properly. Moist curing is the preferred method of curing. If moist curing is not feasible, membrane curing compounds may be used.
Finally, be sure the nozzleman who will be applying shotcrete on your project is certified by the American Concrete Institute (ACI). Certified nozzlemen have been trained and tested on the requirements for proper shotcrete application. Insisting on this certification dramatically increases the probability that you will get the desired results.
RepairQ We are looking at lining an existing 20 ft (6.1 m) diameter brick sewer with shotcrete that is 15 in. (0.4 m) or more thick and fairly heavily reinforced. Can this be done? The existing sewer is about 3 mi (4.8 km) long and 100 years old. Would shotcrete be a suitable method of rehabilitation? The rehabilitation is not just a liner, but the owner wants the shotcrete designed as a replacement pipe inside the existing brick sewer, designed for all earth and other superimposed loads as though the brick sewer were not there.
Yes, this can and should be done in shotcrete. Shotcrete has been used to successfully line brick sewers for 75 years. Shotcrete has been used to line over $40 million worth of brick sewers in Atlanta alone. Large brick sewers have been lined with shotcrete in most of the major midwestern cities. All of them were designed using the existing sewer as a one-sided form. Properly designed and constructed, shotcrete will provide the owner with a new concrete pipe or permanent tunnel lining and the associated expected longevity.
RepairQ We are rehabilitating a limestone-brick masonry storm sewer by lining it with shotcrete. The sewer is approximately 7 ft (2.1 m) tall with an arch ceiling and walls that are 8 ft (2.4 m) apart. The limestone surface is fairly rough, but the brick portions are not. While the existing structure shows no signs of needing to be reinforced for structural support, we are reinforcing to prolong the service life of the culvert. Is there a recommended minimum shotcrete thickness and reinforcement?
Shotcrete has been used to successfully rehabilitate sewers for over 50 years.
The thickness to be used is an engineering issue and beyond the scope of our association. We would recommend a 2 in. (50 mm) minimum thickness reinforced with either polypropylene fibers or a light-gauge welded wire reinforcement. The surfaces must be cleaned thoroughly to remove grease, oils, and other substances deleterious to good bond. Bonding to brick is not a problem.
Finish is another consideration. The added liner thickness will reduce the size of the culvert. If capacity is not an issue, it is recommended to leave the new shotcrete lining with a nozzle finish. If capacity might be a problem, then a float or trowel-smooth finish may be necessary.
RepairQ We are removing up to 0.75 in. (19 mm) of the existing scaled concrete on a fire-damaged concrete wall. The architect has asked if shotcrete is applicable for a vertical 0.75 in. (19 mm) application. Also, the walls are circular and the working distance from the wall is no more than 36 in. (0.9 m). Is this enough room to apply shotcrete?
Yes, shotcrete can be applied in a 36 in. (0.9 m) area. Keep in mind, however, that it’s difficult to get as nice a gunning pattern as you would like when you are that close to the receiving surface. When you cannot back off from the wall, there is a tendency for a more irregular gunning surface, which would require more cutting and screeding to get an aesthetically pleasing result.
RepairQ We are repairing a culvert in Dallas, TX. The concrete wall of the structure is prematurely disintegrating. We are considering a process to temporarily support the ceiling, remove the wall, place a form on one side, and use shotcrete to replace the wall. Does this sound like a reasonable use for shotcrete? What kind of specifications should be used?
Yes, this sounds like a good use of the shotcrete process. Your sequence sounds like a good plan. A sample Structural Shotcrete Specification is available from the Shotcrete magazine archive on the ASA Web site (www.shotcreteweb.wpengine.com/).
RepairQ We are studying a repair to an existing large-diameter corrugated metal pipe. The owner requires that the repair meet the fifth edition of the AASHTO LRFD Bridge Design Specifications with 2010 Interim Revisions. We want the owner to consider shotcrete as opposed to installing a new carrier pipe. I have pipe dimensions, depth, and so on, but need some help deciding if this is practical.
Shotcrete has been used in many cases to repair, rehabilitate, and strengthen pipes, culverts, and tunnels. It is not uncommon to use shotcrete to strengthen a culvert under a highway or roadway section. Shotcrete is a method of placing concrete at a high velocity. The shotcrete placed inside the existing pipe can be designed for strengths from 4000 to 10,000 psi (27.5 to 69 MPa), depending on the amount you are willing to spend on the shotcrete products. We cannot speak to the acceptance by the governing body, but it has been done successfully and often in the past. It is vitally important that the shotcrete contractor be competent and experienced in installing the lining. Your specification should require evidence of similar previously completed projects with current references.
RepairQ We are the Architects of Record for a multi-family rehabilitation here in Portland, OR. The existing building is three stories plus a half basement. It is a historic building and is also an unreinforced masonry building. As a result, it requires significant seismic upgrades. Our structural engineer is proceeding with a design that uses several 4 in. (102 mm) thick shotcrete walls as shear elements throughout the building. In most instances, these walls are being constructed adjacent to an existing wall to minimize their impact to the existing floor plans. This seems fine against the exterior masonry walls but we have concerns where the shotcrete is to be installed directly adjacent to a standard architectural partition (gypsum wall board and wood studs). We are planning on plywood sheathing to act as a one-sided form to prevent the shotcrete application from harming the existing stud wall. However, we were curious if we should also include a water barrier so that the application did not allow moisture to migrate into the existing walls during the installation. Is this assumption correct? And if so, is there a performance or product recommendation that you can offer for this purpose?
Shotcrete has been used in similar structural upgrades for decades quite successfully. There are many ways to ensure that the moisture from the fresh shotcrete would not impact the existing partitions. Methods for protection include use of green board (as used in a shower or bath), plywood, painted coatings, moisture-resistant sheeting, and so on.
Shotcrete is placed with a low water-cement ratio (w/c) and the water is needed by the shotcrete to hydrate the cement and harden. As long as the existing surface or treated surface does not actively absorb the moisture, the shotcrete will use the available internal moisture to hydrate the cementitious materials.RepairQ We are working on a project with a wall that requires additional capacity due to increased loading requirements. We are contemplating shotcrete with additional reinforcing to provide additional thickness for the wall. Is it possible to achieve a composite wall to design for a thicker section for bending, using the bond of the existing concrete and shotcrete along with a reinforcing bar hook anchor epoxied into the existing wall? Any information you can provide would be appreciated.
Shotcrete is often used in similar applications. The question of bending is a structural engineering question. Shotcrete is a method of placing concrete and the properties of shotcrete are similar if not the same as cast concrete. To achieve a composite wall, you must ensure that the existing surface is properly prepared to maximize the potential bond between the overlay shotcrete and the existing wall. Shotcrete placed against a properly prepared existing wall should achieve great bonding strength without the use of bonding agents. Drilled and grouted dowels also contribute to the system, working as a composite wall.
RepairQ We are working on a renovation of an existing shopping plaza where some of the existing walls are split face block. Would it be an acceptable application to resurface the block with shotcrete to achieve a smooth finish? If so, what is the thinnest we would be able to go?
Shotcrete could be used for this application. The thickness of the overlay would be dependent on the material used. A potential concern would be the lines of the existing block showing on the new surface. We would suggest that you search for and review various ASA Shotcrete magazine articles as well as ACI 506R-05, “Guide to Shotcrete”