The embedment depth of anchors in shotcrete would be the same as it would be for conventionally formed and placed concrete. Shotcrete is essentially a method of placing concrete and the same rules would apply. As with any anchoring system, it is important to make sure that you are anchoring to sound material.
We are working on a project with a wall that requires additional capacity due to increased loading requirements. We are contemplating shotcrete with additional reinforcing to provide additional thickness for the wall. Is it possible to achieve a composite wall to design for a thicker section for bending, using the bond of the existing concrete and shotcrete along with a reinforcing bar hook anchor epoxied into the existing wall? Any information you can provide would be appreciated.
Shotcrete is often used in similar applications. The question of bending is a structural engineering question. Shotcrete is a method of placing concrete and the properties of shotcrete are similar if not the same as cast concrete. To achieve a composite wall, you must ensure that the existing surface is properly prepared to maximize the potential bond between the overlay shotcrete and the existing wall. Shotcrete placed against a properly prepared existing wall should achieve great bonding strength without the use of bonding agents. Drilled and grouted dowels also contribute to the system, working as a composite wall.
Can shotcrete be used to help seal a leaking pond? We have a 1.5 acre (6070 m²) pond that we are in the process of completing. We spread 90,000 lb (40,823 kg) of bentonite in, but the bentonite washed off the steep banks and now we are stuck with a half-full pond. Would shotcrete be a practical solution for our problem?
Properly designed shotcrete (both concrete materials and reinforcing are important in the design) placed by an experienced shotcrete contractor can certainly be used to provide a somewhat watertight lining for your pond that will be serviceable, durable, and require little to no maintenance for decades to come. We would suggest you consult with an engineer or shotcrete contractor experienced in this type of shotcrete work. You may use our online Buyers Guide to find an ASA corporate member consultant or contractor to assist you.
I have a new construction project where I want to apply shotcrete to cast-in-place concrete columns and an elevated, post-tensioned concrete slab as a finish material. The finished application is intended to be in varying depths from 3 to 12 in. (76 to 305 mm) or more. The desired end result is a smooth, curvilinear, sculptural form. Is this type of application achievable?
Shotcrete can and has been used to increase the size of columns and thicken overhead slabs while providing great-looking linear or curvilinear finishes. Examples of curvilinear finishes can be found in past Shotcrete magazine articles. You can search the Shotcrete magazine archives.
We are working on a renovation of an existing shopping plaza where some of the existing walls are split face block. Would it be an acceptable application to resurface the block with shotcrete to achieve a smooth finish? If so, what is the thinnest we would be able to go?
Shotcrete could be used for this application. The thickness of the overlay would be dependent on the material used. A potential concern would be the lines of the existing block showing on the new surface. We would suggest that you search for and review various ASA Shotcrete magazine articles as well as ACI 506R-05, “Guide to Shotcrete”
We have a client with a 6 1/2 in. (165 mm) thick reinforced concrete roof slab, the underside of which is in need of repair. There are places where the concrete has spalled, exposing reinforcing bar that has a 3/4 in. (19 mm) cover. There is efflorescence, and there is spalling that does not expose reinforcing bar and some at the steel supporting the concrete slab. In addition, there are hairline cracks and rust spots. Is shotcrete a feasible overhead repair for this situation? What holds the shotcrete to the slab? What is the minimum thickness of shotcrete we should specify? Should we specify shotcrete to be used only at the spalls, cracks, and efflorescence or the whole underside of the slab? Do you have a shotcrete repair procedure that we can put in our specification?
This type of repair is commonly done using the shotcrete process. The extent of the repair is an engineering issue, not a shotcrete issue—shotcrete can and is used for patches and overlays. The shotcrete will adhere to the properly prepared existing concrete. It is installed such that the weight of the plastic shotcrete does not;exceed the adhesion to the existing surfaces; if additional material is needed, it is added at the initial layer or layer set up. The minimum thickness is related to the material used for the repair and the need to establish cover on the existing or added reinforcing. Some repair mortars can be placed as thin as 1/2 in. (13 mm).
Please find a link to a paper on “Concrete Repair by Shotcrete Application”.
The success of the shotcrete repair will be highly dependent upon using a qualified shotcrete contractor and doing an excellent job of preparing the surfaces. Where the reinforcing is exposed, you should require that it be chipped out the entire perimeter allowing for a space of 3/4 in. (19 mm) behind the reinforcing bar so that the repair material can completely encase the reinforcing.
A circular concrete tank built in the 1980s is to be resurfaced due to cracks in the exterior shotcrete lining. It has been proposed that the existing surface will be hydroblasted. Is there a concern that the shotcrete may contain asbestos?
No, there is no reason to assume that the shotcrete would contain asbestos. Shotcrete linings typically contain sand and cement. Asbestos was commonly used for pipe insulation and high-temperature industrial uses and not for shotcrete.
I have been asked to recommend repairs to a fire-damaged brick wall. The wall is 12 in. (30.5 mm) thick and 14 to 16 ft (4.25 to 4.9 m) high. The fire caused spalled brick—3/8 in. (10 mm) deep—and soft mortar joints. The damaged side of the wall is exposed to weather. I plan to recommend tuck-pointing the mortar joints but am wondering if shotcrete is appropriate to repair the spalled brick. The brick could be cut out and replaced, but shotcrete would seem to offer the advantage of repairing and reinforcing the brick wall.
Shotcrete would be an excellent process to repair or overlay your wall. You are correct in saying that it could not only repair but also reinforce and enhance the strength of the wall system. It is important to remove all deteriorated brick and sandblast or water-blast the surface if you are looking for a good bond between the shotcrete and the existing brick. Dowels epoxied or grouted into the existing brick are often used to mechanically tie the shotcrete overlay to the brick wall and also stabilize the new reinforcing steel in the shotcrete overlay.
Can shotcrete be used to repair a wall made of cement and fly ash? If so, should the wall be prepared for the shotcrete application?
Structurally sound concrete that contains up to 20% fly ash in the total cementitious materials should not present any problems for subsequent bonding of shotcrete. Concrete with fly ash contents up to 30% have been used in recent years without any reported problems with strength and bond. Although concrete mixtures with higher levels of fly ash (up to 55%) have been proposed, we don’t have direct experience with their bonding characteristics. We suspect it would be fine as long as the base concrete develops adequate compressive and tensile strength. This could be confirmed by a simple bond strength test of shotcrete on the concrete substrate in question.
The existing surface needs to be properly prepared, removing all soft or deteriorated material back to sound concrete. For extensive defects in the existing concrete, chipping hammers may be required. For removal of light surface carbonation or laitance, a strong, high-pressure water blast or sand/bead blasting may be adequate. Depending on the thickness of the shotcrete, reinforcing may be required in the overlay. Specific details of the repair are best developed by an engineer experienced in shotcrete repair.
We are studying a repair to an existing large-diameter corrugated metal pipe. The owner requires that the repair meet the fifth edition of the AASHTO LRFD Bridge Design Specifications with 2010 Interim Revisions. We want the owner to consider shotcrete as opposed to installing a new carrier pipe. I have pipe dimensions, depth, and so on, but need some help deciding if this is practical.
Shotcrete has been used in many cases to repair, rehabilitate, and strengthen pipes, culverts, and tunnels. It is not uncommon to use shotcrete to strengthen a culvert under a highway or roadway section. Shotcrete is a method of placing concrete at a high velocity. The shotcrete placed inside the existing pipe can be designed for strengths from 4000 to 10,000 psi (27.5 to 69 MPa), depending on the amount you are willing to spend on the shotcrete products. We cannot speak to the acceptance by the governing body, but it has been done successfully and often in the past. It is vitally important that the shotcrete contractor be competent and experienced in installing the lining. Your specification should require evidence of similar previously completed projects with current references.